HOW TO MAKE WHATEVER YOU PRINT LOOK SHARP, GET NOTICED AND READ!

TIPS TO PRODUCE GOOD ORIGINALS

Whenever possible, have your printer work from an original document. If that's not possible it should be nothing more than a first generation copy. Anything else will give poor results

If you're using a computer, final output should be printed on a Laser printer with a resolution of at least 300 dots per inch. 600 DPI, or 800 DPl is noticeably better. In a pinch, Ink Jet printers produce reasonably good output, but stay away from any dot matrix printers that produce ragged text and terrible graphics that will only be magnified when reproduced by your printer or copy machine.

To stand out from the crowd, consider having your masters printed on a ultra-high resolution printer found at many service bureaus in major cities. Typical resolutions start at 1,200 DPI. This is especially important if you employ graphics, photographs, or complex shading patterns. The cost is around fifteen dollars a page.

If you're still using a typewriter, be sure it's an electric model equipped with a high quality carbon ribbon.

Never try and erase from the original. No matter how careful you are, the printer's camera can pick up the deterioration in the paper, make the blemish more noticeable and highlight the very error you're trying to hide.

The same applies to typewriter ribbons that "type over mistakes," the camera will pick it up.

If you must "correct" and are unwilling to redo your work, use a very small amount of one of the many liquid correction fluids. Be sure to match the color of the correction fluid to the paper and let it dry thoroughly.

Avoid using paper clips or folding. Each will put creases in the paper. No staples either, which leave tiny holes that will reproduce as black dots. No masking or cellophane tape which also leave tell-tale marks.

Never use a pencil or marking pens. Neither reproduce evenly or provide enough contrast. Signatures should be made in black ink, being sure you apply steady pressure throughout.

If you want to have a photograph reproduced you need to have it "screened" first. While most quick-print shop can provide this service, you probably can have it done cheaper at your local newspaper office.

WHICH IS BEST, PHOTOCOPYING OR OFFSET PRINTING?

One alternative to offset printing is high quality photocopying. Several national franchises and many retail chain provide excellent work. The key is what type of equipment is available. The typical "pay as you copy" machines that you must feed an endless supply of coins are not suited to running more than a few copies at a time. To get quality and reasonable price I'm talking about expensive full size machines that can copy a two-sided document in one pass anywhere from 50 to 200 copies per minute. If well maintained, the output is excellent and hard to distinguish from offset printing. Your cost should be in the area of four to eight cents a page, which can be a bargain if your need around a hundred copies or so.

If you need more than a few hundred copies, offset printing is cheaper especially in higher quantities. The best way to save is plan ahead. The printer's biggest cost isn't paper or ink which they buy truck loads of at a time, it's labor expense creating, lugging and setting-up the plates in the printing press. So don't have a thousand circulars printed up and come back a month later to repeat the process. You can almost always get a much better price by ordering a six month or greater supply and have them printed all at once.

PAPER AND INK

Harsh color combinations like black ink on red paper should be restricted to large type of a few words only, due to being very hard on the reader's eyes. Reverses (white type set on large black backgrounds) should be limited to small sections like headlines or an attention getting box for the same reason.

Some advertisers have had good success with the newer fluorescent colored papers. While very harsh, they're also bright which gives the necessary contrast to make them work. Because any material printed on this type of paper can overpowering, keep your wording to a minimum and stay away from small text.

ADDITIONAL TIPS TO MAKE YOUR WORK STAND OUT

The importance of white space can not be over emphasized. Never try and squeeze your work into too small an area. While half-inch margins should be considered a minimum for an 8-1/2 x 11 paper, three-quarter to one inch margins generally look better. Be sure to break-up long blocks of text with Sub Heads. Not only do they make whatever you wrote easier to read, it adds visual impact as well.

If you're using a computer don't be tempted to use every font you have in your library. It comes across unprofessional and has the net effect of actually making your work look sloppy and amateurish. For any document you should have no more then three fonts. One for any headline, one for sub-heads and another for the body. Instead of changing fonts, add interest by using either bold or italics You can also make your work look better by varying the size of paragraphs, and indenting or changing the justification on certain key sections. Bullets, borders, and shading in moderation also go a long way to making what ever your writing look better The better your work looks, the more likely it will be read!